how to swag curtains

How To Swag Curtains?

Start by hanging one end of the swag over one end of the rod. Then, hang the other end of the swag over the other end of the rod. Let the fabric in the middle drape down. When you’re finished, the draped fabric in the center should look like a regular curtain swag.

How do you put a swag hook on a curtain?

Hooks are one of the easiest rod substitutes out there. To use them, just install some large hooks on either end of the window. Then, drape the swag curtains over each hook, pulling the curtain through the hooks. To get the classic sag that swags have, then you will need to just pull the middle of the dip down.

How do you hang swag curtains with knots in corners?

Adjust the swags and the curtain to ensure that both hanging sides are equal and the swags are how you want them. Carefully grasp one side of the curtain where it meets the end of the drapery rod. Fold it in half to make a loop and pull the hanging side through the loop to create a loose knot.

How do you pleat a swag curtain?

How do you hang a swag valance and curtain on a single rod?

How long should swag curtains be?

A general rule of thumb is that a swag 45-inches across the top edge requires about 2 yards of fabric. Online fabric calculators, or pattern envelopes, provide the exact amount of fabric required based on fabric type and pattern, mounting method, fabric width and swag measurements.

How do you hang a swag on a curtain rod?

How are swag curtains measured?

Starting from the top of the pole on the left-hand side, take your flexible measuring tape and re-create the arc of the swag over to the top right-hand side of the pole. This is your swag measurement. You need to measure the lowest part of the draped swag in order to get the appropriate amount of fabric.

How do you measure and cut a swag valance?

How do you make a swag valance?

How do you hang a swag curtain without a rod?

To maintain the formal look of pleated curtain panels without having to install a curtain rod, use hook eye screws.
  1. Insert drapery pins across the top of your curtain panel.
  2. Measure the width of the curtain along the top edge and note the distance between the pins.
  3. Mark the pin positions above the window with a pencil.
READ:  how to eat tic tacs

How do you hang double curtains on a single rod?

How do you make a single curtain rod into a double?

How to Convert a Single Curtain Rod to a Double
  1. Purchase a curtain rod conversion kit. …
  2. Remove the existing curtain and curtain rod from the bracket. …
  3. Attach the hardware and brackets from the curtain kit to the wall, using a level to ensure that the curtain rod will be even when installed.

How do you measure swags and tails?

How far down should a valance hang?

A standard valance should have a drop of about 18 to 24 inches. You may be able to make a 16- or 17-inch drop valance work in some cases, but anything less than that may be too short.

How long should tier curtains be?

Tier curtains, which are shorter and generally don’t cover an entire window, are usually either 24 inches or 36 inches long. Curtains are measured from the top of the rod pocket to the end, not from the actual top of the curtain if there is fabric above the rod pocket.

How do you make jabot and swag curtains?

How do you wear sheer over a rod?

Wrapping Around Curtain Rod
  1. Lay the sheer out straight and fold it in half. …
  2. Place the center of the sheer on the center of the curtain rod and attach with a large binder clip or a piece of masking tape. …
  3. Wrap the sheer over the curtain rod several times on each side of the binder clip.

How do you hang a valance over curtains?

How much wider than the window should a valance be?

Most valances should only be 1-1/2 to 5 inches wider than the window if the valance hangs by itself or over a Roman shade. It should be 10 to 30 inches wider than the window if it’s hung over a pair of custom drapes. If the valance is gathered, its total, flat width should be 2 to 3.5 times the width of the window.

READ:  what is the closest beach to greenville nc

What size curtains do I need for a 5ft window?

A common rule for displaying curtains properly says the curtains finished width should be at least 2 times the width of your window (if not more – sheers can be 3 times the window width) to achieve a look of proper fullness.

How wide should a valance be for a 36 inch window?

To determine the width of a valance for a 36-inch window, the Window Treatment Expert website suggests adding 2 to 4 inches on each side, adding less for narrower windows and more for wider windows. For a 36-inch window, this measurement would provide you with a valance that has a width of 40 to 44 inches.

How do you calculate fabric for swags and tails?

Swags – Based on an average of 44″ per swag, you will need 2 yards of fabric per swag. Jabots – Double the longest length, add 4″ and divide by 36. This will give you the number of yards needed for a single pair of Jabots.

How do you line a swag?

How do you cut a waterfall valance?

How do you make a window swag?

How to Sew Window Swags
  1. Measure the width of the window between the ends of the curtain rod or swag knobs. …
  2. Cut a piece of fabric 24 inches wide and to the length you measured. …
  3. Lay the fabric right-side down on your work surface. …
  4. Sew a straight stitch along the fold to secure it in place.

How do you draft a swag pattern?

How do you make a front door swag?

Can you hang curtains without a rod?

You’re missing a great decorative opportunity if you’re not wondering how to hang curtains with or without a rod. … To hang curtains where there weren’t any before, you can put up a rod, but if you don’t want to fix one of these to the wall or prefer a different look, they can be hung without a rod as well.

Can you hang curtain rod with command strips?

Look no further than 3M Command hooks. Yes, the same hooks you use for hanging pictures, keys, mugs, and plants. An easy hack turns them into quick DIY supports for your curtain rod and that splash of color, sun shade, or bit of privacy you’ve been searching for.

READ:  how to flirt with gemini

How do you hang curtains without putting holes in the wall?

Here are five ways to hang curtains without damaging walls or window frames:
  1. Use 3M Command Hooks.
  2. Try Kwik-Hang Curtain Rod Brackets.
  3. Use Tension Rods.
  4. Get Creative With Coat Hooks.
  5. Try Magnetic Rods on Metal Doors.

Do sheer curtains go in front or behind?

When the sheer curtain is the top layer, they’ll hang over your blackout curtains. This lends a visually interesting look for your windows, especially if the two fabrics are paired well based on their pattern and palettes. Sheers are always visible being the top layer.

What are the different ways to hang curtains?

Rod pocket, eyelet and tab top are amongst the most popular ways to hang curtains.
  1. Rod Pocket. The most basic heading is the rod pocket (also known as pole pocket) style. …
  2. Curtain rings. Using curtain rings is a popular choice. …
  3. Eyelet. …
  4. Tab Top. …
  5. Tie Top. …
  6. Pencil pleat. …
  7. Goblet pleat. …
  8. Pinch pleat.

Do curtains have to touch the floor?

Yes, curtains should be long enough to touch the floor. With a few exceptions, the longer the curtains are the more stylish and elegant it will look. This is why most standard ready-made curtains are lengthy. But the reality is that various decorating styles use different curtain lengths.

Video #41: Tips From Us: Swag Curtains – How to hold swag curtains in place

How to Fold a Scarf for Window Decorating : Unique Interior Decorating Ideas

How to make swags/ DIY

*Elegant Swag Curtain* | Diy simple CURTAIN Full Tutorial for beginners

How to make curtains swags 2

Related Searches

curtain swag holders
how to wrap curtains around curtain rods youtube
how to hang swags
ways to hang a valance
swag curtains for living room
how to drape curtains to one side
how to hang swag curtains without a rod
how to drape curtains for backdrop

See more articles in category: FAQ